input stringclasses 1
value | instruction stringlengths 228 3.39k | output stringlengths 287 3.32k | category stringclasses 1
value | index stringclasses 1
value | fileName null |
|---|---|---|---|---|---|
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾚﾊﾞｰ取付け",
"Words": [
"ﾚﾊﾞｰ1",
"ﾚﾊﾞｰ2",
"ﾚﾊﾞｰ3"
],
"WorkItems": [
"1. ⑥にCOLLAR ⑦⑧をPIN で取付ける",
"2. ㉘を取り外す"
],
"WorkPoints": [
"各ﾚﾊﾞｰを揺動させ引っかかりなく動作すること",
"➀にて締結時、㉘を抑えて取付のこと※六角ナットが飛び出てしまう恐れがある為"
],
"Tolk... | [
{
"WorkName": "ﾚﾊﾞｰ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け1",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1×4ヶ所"
],
"WorkItems": [
"◆1. ⑥にSPRING SPRING を取付ける"
],
"WorkPoints": [
"ﾌｯｸの向きに注意",
"確実に溝に入っているか確認する事",
"ｽﾌﾟﾘﾝｸﾞﾌｯｸの外れ無い事"
],
"Tolks": [],
"InspectionItems": [
"... | [
{
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け1",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ｾﾝｻ取付け2",
"Words": [],
"WorkItems": [
"1. ⑥にSENSOR をSCREW WASHER で取付ける",
"2. ㉘で配線を固定する"
],
"WorkPoints": [
"SENSOR はﾊﾞｶ穴分上･右側に寄せて取付け",
"乗り上げ注意",
"LEDが見える向きで取付ける",
"配線がﾌﾚｰﾑ側面がら飛び出さないようｶﾌﾟﾄﾝﾃｰﾌﾟで固定"
],
"Tolks"... | [
{
"WorkName": "ｾﾝｻ取付け2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "17cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"Words": [
"向き",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:2",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1×2ヶ所",
"支点ﾋﾟﾝ"
],
"WorkItems": [
"◆1. PIN を㉙にセットし⑤を倒す",
"◆2. SPRING をｾｯﾄしCOLLAR SCREW で取付け",
"3. ｽﾌﾟﾘﾝｸﾞのﾌｯｸをかける"
],
"WorkPoints": [
"㉙に... | [
{
"WorkName": "ｽﾌﾟﾘﾝｸﾞ取付け2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "15cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾌﾞﾛｯｸ取付け",
"Words": [],
"WorkItems": [
"1. ⑥にBLOCK をBOLT で取付ける"
],
"WorkPoints": [
"当付けて固定する"
],
"Tolks": [
"締付ﾄﾙｸ 40cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ｾﾝｻ取付け1",
"Words": [],
"WorkItems": [
"1. ⑥にSENSOR ､COVER をSCREW で取付ける"
],
"WorkPoints": [
"配線のはさみこみ無きこと",
"ｶﾌﾟﾄﾝﾃｰﾌﾟを貼る配線のはさみこみ無きこと",
"COVER は上に押し当てながら締結のこと",
"SENSOR は㉘を使って位置決めをする事(2箇所)"
],
"Tolks": [
"締付ﾄ... | [
{
"WorkName": "ｾﾝｻ取付け1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾄﾞﾗｲﾊﾞｰ基板取付け",
"Words": [
"上側"
],
"WorkItems": [
"■★1. ⑤にSHEET MOTOR-DRIVER をSCREW で取付ける"
],
"WorkPoints": [
"白ｺﾈｸﾀが並んでいる側を上側にすること",
"SHEET は2枚重なっていてもわかりづらいので取付時､注意のこと",
"型式:MU001-8111-D"
],
"Tolks": [
"締... | [
{
"WorkName": "ﾄﾞﾗｲﾊﾞｰ基板取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "配線",
"Words": [],
"WorkItems": [
"★1. 基盤に配線を接続する",
"2. ｹｰﾌﾞﾙをとめる"
],
"WorkPoints": [
"ｺﾈｸﾀの向きに注意",
"ｺﾈｸﾀの向きに注意",
"空き",
"1→2→3の順番に接続して配線の負荷がかからないようにすること",
"ｺﾈｸﾀを接続したら青ﾏｰｷﾝｸﾞをする"
],
"Tolks": [],
"Inspe... | [
{
"WorkName": "配線",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"WorkName": ... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"Words": [],
"WorkItems": [
"1. ⑤にMOTOR をBOLT で取付け､PLATE をSCREW BOLT で取付ける"
],
"WorkPoints": [
"ﾓｰﾀのｹｰﾌﾞﾙは下図のように通すこと",
"ｻｲﾄﾞﾌﾟﾚｰﾄとﾌﾚｰﾑの段差を手感で確認しﾌﾚｰﾑと同じ高さ或いはﾌﾚｰﾑより出ていないこと",
"㉜を⑤に押し当てクランプをロックする",
"㉜に... | [
{
"WorkName": "送りﾓｰﾀｰ・ｻｲﾄﾞﾌﾟﾚｰﾄ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames"... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "引き込みﾓｰﾀｰ取付け1",
"Words": [
"裏面の写真"
],
"WorkItems": [
"1. ⑥にMOTOR をBOLT で取付ける"
],
"WorkPoints": [
"樹脂ｶﾞｲﾄﾞでMOTOR の歯が隠れている事",
"ｹｰﾌﾞﾙを先に入れる",
"ﾓｰﾀのﾋﾟﾝをﾌﾚｰﾑの穴に入れること",
"➀を入れる時に、➀のスプロケットが樹脂ガイドに乗り上げるためこの樹脂ガイドを下げながら取付のこ... | [
{
"WorkName": "引き込みﾓｰﾀｰ取付け1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "100cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "引き込みﾓｰﾀｰ取付け2",
"Words": [],
"WorkItems": [
"1. ⑥にSCREW を取付ける"
],
"WorkPoints": [
"先にｾﾝｻｰのｺﾈｸﾀを挿して青ﾏｰｷﾝｸﾞ",
"ﾈｼﾞを締めた後で､配線をｶﾌﾟﾄﾝﾃｰﾌﾟで固定する",
"配線経路に押し込むようにﾃｰﾌﾟでとめる"
],
"Tolks": [
"締付ﾄﾙｸ 30cN･m"
],
"InspectionIt... | [
{
"WorkName": "引き込みﾓｰﾀｰ取付け2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "矯正ｶﾞｲﾄﾞ取付け1",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1x4箇所"
],
"WorkItems": [
"◆2. SPRING をｾｯﾄする",
"3. ➁をセットして㉘を下図のように挿入",
"1. ⑩に⑥をｾｯﾄする"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkT... | [
{
"WorkName": "矯正ｶﾞｲﾄﾞ取付け1",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "矯正ｶﾞｲﾄﾞ取付け2",
"Words": [
"ﾃｰﾌﾟ押さえｶﾞｲﾄﾞ",
"隙間"
],
"WorkItems": [
"1. ⑤のﾌﾟﾚｰﾄ部をSCREW で取付ける",
"2. GUIDE をSCREW で仮付けする",
"3. 矯正ガイドに㉚をセットしSCREW を本締めする"
],
"WorkPoints": [
"SCREW 取付後㉛を取り外す",
"GUIDE の穴とｼｬﾌﾄの凸部を合わ... | [
{
"WorkName": "矯正ｶﾞｲﾄﾞ取付け2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "25cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "矯正ｶﾞｲﾄﾞ取付確認",
"Words": [
"矯正ｶﾞｲﾄﾞ測定ｼﾞｸﾞ固定部",
"矯正ｶﾞｲﾄﾞ測定ｼﾞｸﾞ可動部",
"矯正ｶﾞｲﾄﾞ前側",
"矯正ｶﾞｲﾄﾞ後側"
],
"WorkItems": [
"1. ①の矯正ｶﾞｲﾄﾞの取付け後の幅を測定する",
"2. ブザーON（もしくは赤ランプON）したらOKとし㉖を外す"
],
"WorkPoints": [
"ﾎﾞﾙﾄの頭をかわしてｾｯﾄす... | [
{
"WorkName": "矯正ｶﾞｲﾄﾞ取付確認",
"QualityItem": "寸法確認",
"ToolManageNo": "FM-4783",
"ToolName": "矯正ｶﾞｲﾄﾞ測定ｼﾞｸﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "WDKC-G09-001",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾒｲﾝﾓｰﾀｰ取付け",
"Words": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ",
"ﾌﾚｷのﾀﾌﾞ",
"ｱｸﾁｭｴｰﾀの溝"
],
"WorkItems": [
"★1. ①の引き込みﾓｰﾀｰのﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"ﾛｯｸを外しｹｰﾌﾞﾙをｾｯﾄしﾛｯｸする",
"ﾛｯｸを外しｹｰﾌﾞﾙを奥まで挿入してﾛｯｸする",
"ｺﾈｸﾀを繋げたら青ﾏｰｷﾝ... | [
{
"WorkName": "ﾒｲﾝﾓｰﾀｰ取付け",
"QualityItem": "接続確認",
"ToolManageNo": "FM-4187",
"ToolName": "ﾌﾗｯﾄｹｰﾌﾞﾙ挿入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ取付け(細)1",
"Words": [
"OK",
"使用治工具No.28",
"使用治工具No.28"
],
"WorkItems": [
"1. CABLE を⑦に接続する",
"2. ｱｸﾁｭｴｰﾀｰの端子を⑦に取付ける",
"★3. ⑦の基板をWASHER SCREW で取付ける"
],
"WorkPoints": [
"CABLE の端子面を上側にする",
"ﾛｯｸす... | [
{
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ取付け(細)1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "30cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ取付け(細)2",
"Words": [
"基準"
],
"WorkItems": [
"★1. ﾌﾗｯﾄｹｰﾌﾞﾙ配線･接続する",
"★2. 整線する"
],
"WorkPoints": [
"ﾌﾚｰﾑ下側を通す",
"この箇所の曲げは全体の配置が決まってから折る",
"直角になるように配置する",
"ｶﾌﾟﾄﾝﾃｰﾌﾟを貼りｹｰﾌﾞﾙをとめる",
"両面ﾃｰﾌﾟの真ん中あた... | [
{
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ取付け(細)2",
"QualityItem": "負荷確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｹｰﾌﾞﾙに負荷がかかって無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "操作SW・ﾌﾗｯﾄｹｰﾌﾞﾙ(太)取付け",
"Words": [],
"WorkItems": [
"2. ケーブル関係を㉘でとめる",
"3. ﾌﾗｯﾄｹｰﾌﾞﾙを折り曲げる",
"1. SWITCH にCABLE を取付けてから⑩にSCREW で取付ける"
],
"WorkPoints": [
"先にCABLE と⑩をSWITCH のｺﾈｸﾀに接続し青ﾏｰｷﾝｸﾞする",
"ﾌﾚｰﾑへの乗り上げﾌﾗｯﾄｹｰﾌﾞﾙ折曲がり等注意... | [
{
"WorkName": "操作SW・ﾌﾗｯﾄｹｰﾌﾞﾙ(太)取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ配線(太)",
"Words": [
"OK",
"NG",
"※使用治工具No.26"
],
"WorkItems": [
"★1. ①のﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"突き当たりまで押し込んでﾛｯｸする(ｺﾈｸﾀｰに対して傾きが無い事)",
"接続後､青ﾏｰｷﾝｸﾞ",
"ﾌﾚｰﾑ下側を通す",
"一度折り曲げた箇所は開... | [
{
"WorkName": "ﾌﾗｯﾄｹｰﾌﾞﾙ配線(太)",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "引き込みﾓｰﾀｰ取付け",
"Words": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ",
"ﾌﾚｷのﾀﾌﾞ",
"ｱｸﾁｭｴｰﾀの溝",
"ｱｸﾁｭｴｰﾀを確実にﾛｯｸすることﾌﾚｷは折り曲げないことｺﾈｸﾀを繋げたら青ﾏｰｷﾝｸﾞする",
"使用治工具No.26"
],
"WorkItems": [
"★1. ①の引き込みﾓｰﾀｰのﾌﾗｯﾄｹｰﾌﾞﾙを引き回し､基板に接続する"
],
"WorkPoints": [
"... | [
{
"WorkName": "引き込みﾓｰﾀｰ取付け",
"QualityItem": "接続確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り接続出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Wo... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"Words": [
"2.5mm",
"ｸｯｼｮﾝ"
],
"WorkItems": [
"1. ⑤に②を挟みながら①を取付ける(共締め)"
],
"WorkPoints": [
"固定時に②が浮かない様注意(幅検査でNGになる)",
"2.5mmのﾌﾞﾛｯｸｹﾞｰｼﾞを挟んでﾎﾞﾙﾄを締めてきつくなったところでﾅｯﾄを締結",
"ﾅｯﾄ締結時､②のｸｯｼｮﾝ部をつぶさないように締... | [
{
"WorkName": "ﾃｰﾌﾟ規正ｶﾞｲﾄﾞ取付け",
"QualityItem": "隙間確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "隙間:2.5㎜",
"Method": "ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "側面ｶﾊﾞｰ取付け",
"Words": [],
"WorkItems": [
"1. ⑤にSLIDER UNIT を入れた状態でCOVER をSCREW で取付ける"
],
"WorkPoints": [
"ﾌﾗｯﾄｹｰﾌﾞﾙ部",
"ﾒｲﾝﾓｰﾀｹｰﾌﾞﾙ",
"束線",
"引き込みﾓｰﾀｹｰﾌﾞﾙ･ﾌﾗｯﾄｹｰﾌﾞﾙ",
"先端部から順番に締め込む事",
"配線の挟み込み無き事",
"⑤の穴にSL... | [
{
"WorkName": "側面ｶﾊﾞｰ取付け",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "ｵｰﾄﾛｰﾄﾞﾌｨｰﾀﾞ「（AL）：本体組立（501-）",
"WorkName": "ｶﾊﾞｰ取付け1",
"Words": [],
"WorkItems": [
"1. ⑥にCOVER PLATE をSCREW で取付け､ﾓｰﾀをSCREW で取付ける"
],
"WorkPoints": [
"SCREW とSCREW の長さの違いに注意",
"M3×6 白",
"M3×5 黒",
"COVER は重なっていてもわかりづらいので注意のこと",
"配線の噛み込み注意"
],
"Tolks": [... | [
{
"WorkName": "ｶﾊﾞｰ取付け1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "60cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾍﾞｱﾘﾝｸﾞ準備",
"Words": [
"※D-pin(2ヶ所)と穴(2ヶ所)を はめ込む(赤矢印参照)"
],
"WorkItems": [
"1. 治具(FM-2250)にBEARING を挿入し 上治具をｾｯﾄする",
"2. 1.完成品の上治具の穴に､PIN を挿入･圧入する",
"3. 2.完成品の上治具を外し､ SPACER を挿入する"
],
"WorkPoints": [
"治具... | [
{
"WorkName": "ﾍﾞｱﾘﾝｸﾞ準備",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2250",
"ToolName": "ﾍﾞｱﾘﾝｸﾞDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｼｬｯﾀｰ仮組",
"Words": [],
"WorkItems": [
"1. SHUTTER BLOCK COLLAR GUIDE GUIDE をBOLT で仮組"
],
"WorkPoints": [
"取付方向注意",
"取付方向注意",
"黄色面は端面合わせの事",
"緑色面は押し当ての事",
"SD-A000800-016で締付"
],
"Tolks": [],
"... | [
{
"WorkName": "ｼｬｯﾀｰ仮組",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｽﾄｯﾊﾟｰ前組",
"Words": [
"接着剤塗布 米粒:2"
],
"WorkItems": [
"▲1. BLOCK にSTOPPER を接着剤で取付"
],
"WorkPoints": [
"ｱﾙｺｰﾙで清掃後､BLOCK の取付穴にｽｰﾊﾟｰXを塗布し､STOPPER を取付ける",
"飛び出した接着剤は拭き取りの事",
"ﾃｰﾊﾟ側を挿入"
],
"Tolks": [],
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ前組",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "接着剤ｽｰﾊﾟｰX",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾛﾝｸﾞﾋﾟﾝ圧入",
"Words": [
"出代39mm",
"FM-2252①",
"FM-2252②"
],
"WorkItems": [
"1. PIN をBLOCK に圧入"
],
"WorkPoints": [
"ﾋﾟﾝ出代:39㎜",
"圧入後､指で引っ張り抜け無い事を確認",
"ﾋﾟﾝのﾃｰﾊﾟ側から圧入する事",
"治具BLOCK にPIN を挿入する... | [
{
"WorkName": "ﾛﾝｸﾞﾋﾟﾝ圧入",
"QualityItem": "出代確認",
"ToolManageNo": "FM-2252",
"ToolName": "ﾊﾞﾈｶﾞｲﾄﾞ､Dﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾌﾞﾛｯｸDﾋﾟﾝ圧入",
"Words": [
"3㎜",
"3㎜",
"2個作成",
"FM-2253(下側)",
"FM-2253(上側)",
"治具(上側)を被せ②を入れ圧入",
"この作業では同じものを2個製作"
],
"WorkItems": [
"2. 1完成品にPIN を圧入",
"1. BLOCK に砥石を掛ける"
],
"WorkPoints... | [
{
"WorkName": "ﾌﾞﾛｯｸDﾋﾟﾝ圧入",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ・ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"W... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｽﾍﾟｰｻｰﾌﾞﾛｯｸ組立",
"Words": [],
"WorkItems": [
"1. BLOCK にSPACER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels":... | [
{
"WorkName": "ｽﾍﾟｰｻｰﾌﾞﾛｯｸ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾍﾞｰｽ組立①",
"Words": [
"表面",
"裏面",
"側面",
"側面"
],
"WorkItems": [
"1. BASE に油砥石をかける"
],
"WorkPoints": [
"表面 裏面 側面に砥石をかけ､ﾊﾞﾘ･ｶｴﾘ等の取り除く"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "ﾍﾞｰｽ組立①",
"QualityItem": "表面確認",
"ToolManageNo": "-",
"ToolName": "油砥石",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ﾊﾞﾘ・ｶｴﾘ等無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾍﾞｰｽ組立②",
"Words": [],
"WorkItems": [
"1. ①にPIN を圧入"
],
"WorkPoints": [
"表裏に注意",
"出代1.5㎜"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾍﾞｰｽ組立②",
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾍﾞｰｽ組立③",
"Words": [],
"WorkItems": [
"1. ①に②を圧入"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"JiguNo": "使用治工具Ｎｏ.26",
... | [
{
"WorkName": "ﾍﾞｰｽ組立③",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾍﾞｰｽ組立④",
"Words": [],
"WorkItems": [
"1. ①にHOLDER をBOLT で取付"
],
"WorkPoints": [
"ﾍﾞｰｽのDﾋﾟﾝに挿入した後､ﾎﾞﾙﾄを締結の事"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes":... | [
{
"WorkName": "ﾍﾞｰｽ組立④",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "裏面ﾍﾞｱﾘﾝｸﾞ取付",
"Words": [],
"WorkItems": [
"1. ①にBEARING SPACER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels"... | [
{
"WorkName": "裏面ﾍﾞｱﾘﾝｸﾞ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾌﾞﾛｯｸ取付①",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT で取付"
],
"WorkPoints": [
"ﾃｰﾊﾟ側を下側にて挿入"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolParts... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付①",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾌﾞﾛｯｸ取付②",
"Words": [],
"WorkItems": [
"1. ①にBLOCK BLOCK をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 150cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾌﾞﾛｯｸ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｸﾞﾘｰｽ塗布",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各1"
],
"WorkItems": [
"◆1. ①のﾍﾞｱﾘﾝｸﾞにｸﾞﾘｰｽを塗布する"
],
"WorkPoints": [
"ﾍﾞｱﾘﾝｸﾞ(8箇所)にｸﾞﾘｰｽ塗布"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": ... | [
{
"WorkName": "ｸﾞﾘｰｽ塗布",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｼｬｯﾀｰ取付①",
"Words": [],
"WorkItems": [
"1. ①に②を挿入",
"2. COLLAR をBOLT で仮付け"
],
"WorkPoints": [
"挿入方向に注意",
"SD-A000800-016で締付"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes... | [
{
"WorkName": "ｼｬｯﾀｰ取付①",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｼｬｯﾀｰ取付②",
"Words": [],
"WorkItems": [
"1. ﾍﾞｱﾘﾝｸﾞの当たり調整",
"2. 調整後､仮付けだったﾎﾞﾙﾄを締結",
"3. 中央部にCOLLAR をBOLT で取付"
],
"WorkPoints": [
"P008(SD-A000800-02参照)側を下にして､ｼｬｯﾀｰ動作時に各ﾍﾞｱﾘﾝｸﾞが回転するように調整"
],
"Tolks": [
... | [
{
"WorkName": "ｼｬｯﾀｰ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｽﾄｯﾊﾟｰ取付①",
"Words": [
"接着剤塗布 米粒:1",
"3㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ",
"φ3.01ﾋﾟﾝｹﾞｰｼﾞ"
],
"WorkItems": [
"▲1. ①に②をBOLT WASHER で仮付け",
"2. ②の位置調整後､BOLT を締結"
],
"WorkPoints": [
"ﾋﾟﾝｹﾞｰｼﾞを挿入し､ｼｬｯﾀｰの間にﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込む",
... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ取付①",
"QualityItem": "接着量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ﾛｯｸﾀｲﾄ242/243",
"ProcessNames": [
"-"
]
},
{
"W... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"Words": [],
"WorkItems": [
"1. ①にSPACER WASHER をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [... | [
{
"WorkName": "ｽﾄｯﾊﾟｰ取付②",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾊﾞﾈ取付",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1"
],
"WorkItems": [
"◆1. ②SPRING WASHER にｸﾞﾘｰｽを塗布",
"2. ①に②をBOLT で取付しSPRING を挿入",
"3. GUIDE にWASHER を貼付けし､BOLT WASHER で取付"
],
"Work... | [
{
"WorkName": "ﾊﾞﾈ取付",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒:各2ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
"... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｶﾞｲﾄﾞ取付",
"Words": [
"FM-4119",
"ｸﾞﾘｰｽ塗布 小豆:1"
],
"WorkItems": [
"◆2. GUIDE の内側にｸﾞﾘｰｽを塗布する",
"1. ①にGUIDE をBOLT WASHER で取付"
],
"WorkPoints": [
"治具にて取付位置調整を行う",
"治具ﾌﾞﾛｯｸにGUIDE を押し当てて取付",
"調整後押し当... | [
{
"WorkName": "ｶﾞｲﾄﾞ取付",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4119",
"ToolName": "ｶﾞｲﾄﾞ位置調整治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付け出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ｽﾍﾟｰｻｰ取付",
"Words": [],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"2. 裏面にSPACER をBOLT で取付"
],
"WorkPoints": [
"①のﾍﾞｰｽﾌﾟﾚｰﾄ下面と側面に､②の下面と側面の位置をそろえる"
],
"Tolks": [
"締付ﾄﾙｸ 95cN･m",
"締付ﾄﾙｸ 95cN･m"
],
... | [
{
"WorkName": "ｽﾍﾟｰｻｰ取付",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "ﾗﾍﾞﾙ貼付け",
"Words": [
"0.5㎜",
"72㎜",
"1㎜",
"78㎜",
"21㎜",
"1.5㎜"
],
"WorkItems": [
"1. ①にLABEL LABEL ④を貼付"
],
"WorkPoints": [
"貼付け面の脱脂･清掃後ﾗﾍﾞﾙ貼付けの事"
],
"Tolks": [],
"InspectionItem... | [
{
"WorkName": "ﾗﾍﾞﾙ貼付け",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示寸法:各±0.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "機能検査①",
"Words": [
"FM-2902"
],
"WorkItems": [
"1. ｼｬｯﾀｰ動作を確認",
"2. ﾉｽﾞﾙﾁｪﾝｼﾞｬｰの着脱確認をする"
],
"WorkPoints": [
"ｼｬｯﾀｰが開く時のｽﾄﾛｰｸ摺動抵抗を測定(4.2N以下)"
],
"Tolks": [],
"InspectionItems": [
"検査表①:ｼｬｯﾀｰ動作確認... | [
{
"WorkName": "機能検査①",
"QualityItem": "動作確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾟｯｼｭﾌﾟﾙｹﾞｰｼﾞ",
"ToolCycle": "1回/1年",
"ToolRecord": "校正成績書",
"StdVal": "4.2N以下",
"Method": "目視",
"RecordMethod": "WDQB-F013-019",
"Others": "-",
"ProcessNames": [
"-"
]... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2： ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ/L（12ﾉｽﾞﾙﾍｯﾄ）（001-024）",
"WorkName": "機能検査②",
"Words": [
"･自重落下する事",
"･ﾚﾊﾞｰを押す",
"･ｼｬｯﾀｰ｢開閉｣ｽｲｯﾁ",
"FM-2169"
],
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰの自重落下確認",
"2. ﾉｽﾞﾙの挿抜確認をする"
],
"WorkPoints": [
"･引っかかりが無くｽﾑｰｽﾞな事･ﾉｽﾞﾙに遊びがある事･ｼｬｯﾀｰが閉じた状態でﾉｽﾞ... | [
{
"WorkName": "機能検査②",
"QualityItem": "挿抜確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "ｽﾑｰｽﾞである事",
"Method": "目視",
"RecordMethod": "WDQB-F013-019",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾗﾍﾞﾙ貼付け_1",
"Words": [
"1mm",
"1mm"
],
"WorkItems": [
"1. BRACKET へLABEL を貼付ける"
],
"WorkPoints": [
"BRACKET の貼付け部分の油分･ごみ等を除去する"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"To... | [
{
"WorkName": "ﾗﾍﾞﾙ貼付け_1",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"Words": [
"締付ﾄﾙｸ 1.2N･m"
],
"WorkItems": [
"1. 1.VALVE にJOINT SILENCER JOINT を取付",
"2. 1完成品にTUBE を取付"
],
"WorkPoints": [
"ｻｲﾚﾝｻの根元を掴んで取付けの事",
"TUBE を115㎜にｶｯﾄする"
],
"Tolks": [],
"InspectionItems": [],
... | [
{
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Work... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｼﾘﾝﾀﾞ部組立(1/4)",
"Words": [],
"WorkItems": [
"1. BLOCK にSPACER BEARING をBOLT で取付"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ｼﾘﾝﾀﾞ部組立(1/4)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"Words": [
"◆作業者安全作業",
"②",
"③",
"④",
"付属ﾅｯﾄ",
"⑥",
"①",
"締付ﾄﾙｸ 95cN･m",
"⑦",
"締付けﾄﾙｸ:1.2N･m",
"⑤",
"付属ﾅｯﾄ",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸ... | [
{
"WorkName": "ｼﾘﾝﾀﾞ部組立(2/4)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｼﾘﾝﾀﾞ部組立(3/4)",
"Words": [
"締付ﾄﾙｸ 1.2N･m",
"締付けﾄﾙｸ: 95cN･m",
"ｼｯｸﾈｽｹﾞｰｼﾞ0.5㎜",
"N020部を避けながら､定盤で組立"
],
"WorkItems": [
"1. ①に②③を⑯で取付",
"2. ①に⑤を取付"
],
"WorkPoints": [
"③は 直角に取付 (定盤部で 当付け)",
"ｾﾝｻｰ取付位置を③側にすること",... | [
{
"WorkName": "ｼﾘﾝﾀﾞ部組立(3/4)",
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolName": "位置合わせ治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"Words": [
"ｼﾘﾝﾀﾞｰ戻限用LS(B01/11R)",
"ＬＳ調整位置 （ 約3mm ） ⇩",
"ｺﾈｸﾀｰへ",
"左側より近づけてONする位置",
"ｾﾝﾀｰ",
"ｾﾝﾀｰ",
"LS調整位置 ( 約3mm )",
"右側より近づけてONする位置",
"ﾏｰｷﾝｸﾞ",
"ﾏｰｷﾝｸﾞ",
"ｼﾘﾝﾀﾞｰ出限用LS(B02/12R)",
... | [
{
"WorkName": "ｼﾘﾝﾀﾞ部組立(4/4)",
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolName": "位置合わせ治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "LEVER部組立(1/4)P005ﾌﾞﾛｯｸへﾋﾟﾝ圧入",
"Words": [
"1. ①を②に挿入し油砥石をかけた部分に防錆油を塗布する",
"ﾋﾟﾝ出代:3.5mm",
"S-Pinの割り部分をこちら側へ",
"3.5mm"
],
"WorkItems": [
"1. BRACKET の赤の指示部に油砥石をかける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems":... | [
{
"WorkName": "LEVER部組立(1/4)P005ﾌﾞﾛｯｸへﾋﾟﾝ圧入",
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolName": "ﾌﾞﾗｹｯﾄﾋﾟﾝ圧入治具ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "LEVER部組立(2/4)",
"Words": [
"①",
"③",
"締付けﾄﾙｸ: 320cN･m",
"締付けﾄﾙｸ: 150cN･m",
"②",
"⑰",
"②",
"③",
"①",
"④",
"⑯",
"･外周にｸﾞﾘｰｽ塗布米粒:2"
],
"WorkItems": [
"1. PLATE LEVER に砥石をかける",
"◆2. WASHE... | [
{
"WorkName": "LEVER部組立(2/4)",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "LEVER部組立(3/4)",
"Words": [
"締付けﾄﾙｸ: 200cN･m",
"⑯",
"①",
"①"
],
"WorkItems": [
"1. ①をﾊﾞｲｽに取付",
"2. ①へ②を⑯で取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
... | [
{
"WorkName": "LEVER部組立(3/4)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "200cN・m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "LEVER部組立(4/4)",
"Words": [
"③",
"②",
"①",
"④⑰",
"③",
"⑤",
"⑯",
"⑯",
"⑥",
"LCG100",
"締付ﾄﾙｸ 3.2N･m",
"締付ﾄﾙｸ 3.2N･m",
"･摺動面にｸﾞﾘｰｽ塗布 米粒:2",
"･切削面にｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"1.... | [
{
"WorkName": "LEVER部組立(4/4)",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(1/3)",
"Words": [
"表裏部",
"左右上面",
"端面"
],
"WorkItems": [
"1. LEVER LEVER BRACKET SHAFT の指示部を面取りする"
],
"WorkPoints": [
"面取りの箇所は取付け部か摺動部の為充分に拭きあげておくこと｡"
],
"Tolks": [],
"InspectionItems": [],
"Inspectio... | [
{
"WorkName": "ｸﾗﾝﾌﾟ部の組立(1/3)",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(2/3)",
"Words": [
"⑥",
"⑦",
"⑰⑱",
"⑰⑱",
"①",
"②",
"⑯",
"⑰",
"④",
"⑤",
"③",
"⑦",
"⑥",
"⑦",
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:1(2ヵ所)"
],
"WorkItems": [
"1. SPACER にBEARING WASHER ⑤をBOL... | [
{
"WorkName": "ｸﾗﾝﾌﾟ部の組立(2/3)",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｸﾗﾝﾌﾟ部の組立(3/3)",
"Words": [
"A",
"A",
"B",
"B",
"締付ﾄﾙｸ 150cN･m"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. Aを締付け",
"3. Bを締付け"
],
"WorkPoints": [
"浮きが無いこと確認しﾚｰﾊﾞｰを締めて固定する",
"締付けの際浮きが無いことを確認し締付ける",
... | [
{
"WorkName": "ｸﾗﾝﾌﾟ部の組立(3/3)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4062",
"ToolName": "ｸﾗﾝﾌﾟ部組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾌﾟﾚｰﾄ(A002)の面取り",
"Words": [
"※砥石掛け部"
],
"WorkItems": [
"1. PLATE に油砥石をかける"
],
"WorkPoints": [
"指示部分にかける事"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "ﾌﾟﾚｰﾄ(A002)の面取り",
"QualityItem": "作業確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに作業してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "PLATE部組立(1/4)S-PIN圧入とｶﾞｲﾄﾞの取付",
"Words": [
"5㎜",
"11㎜",
"FM-2254",
"⑤",
"④",
"A",
"B"
],
"WorkItems": [
"1. ①へ②③を圧入する",
"2. ①に④⑤を⑯⑰で取付け"
],
"WorkPoints": [
"ﾋﾟﾝの出代に注意 (5㎜･11㎜)",
"この工程では仮取付け､本... | [
{
"WorkName": "PLATE部組立(1/4)S-PIN圧入とｶﾞｲﾄﾞの取付",
"QualityItem": "出代確認",
"ToolManageNo": "-",
"ToolName": "圧入治具ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:5㎜出代:11㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "PLATE部組立(2/4)",
"Words": [
"締付けﾄﾙｸ: 95cN･m",
"③⑰",
"⑯④②③",
"②",
"④",
"③",
"⑯",
"⑤⑥",
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"◆1. SPRING ･SPACER にｸﾞﾘｰｽを塗布",
"2. BOLT にSPRING WASHER SPACER を通す",
"3. ①... | [
{
"WorkName": "PLATE部組立(2/4)",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/2粒",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "PLATE部組立(3/4)",
"Words": [],
"WorkItems": [
"2. SENSOR へLABEL を取付け"
],
"WorkPoints": [
"被服ﾁｭｰﾌﾞ端面とﾗﾍﾞﾙの端面を合わせること"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
... | [
{
"WorkName": "PLATE部組立(3/4)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "PLATE部組立(4/4)",
"Words": [
"⑯⑰⑱",
"②",
"ｾﾝｻｰの矢印方向注意",
"刻印有り",
"ﾌﾛﾝﾄ用B06R",
"ﾌﾛﾝﾄ用B05R",
"ﾌﾛﾝﾄ用B04R",
"ﾌﾛﾝﾄ用B03R",
"ﾘｱ用B16R",
"ﾘｱ用B15R",
"ﾘｱ用B14R",
"ﾘｱ用B13R",
"当付方向",
"※ｾﾝｻｰの刻印側を図の方向とする｡※ｾﾝ... | [
{
"WorkName": "PLATE部組立(4/4)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(1/3)",
"Words": [
"⑱⑲",
"③"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"2. ①に③をBOLT WASHER で取付",
"2. ②の裏へCLIP をBOLT で取付"
],
"WorkPoints": [
"調整後に指定ﾄﾙｸで仮締め締付けはSD-A000962-024にて締め付け",
"調整後に指定ﾄﾙｸで仮締め締付けはSD-... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ(1/3)",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"Wo... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "配線・JOINT取付",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定",
"③",
"②"
],
"WorkItems": [
"1. .配線を固定する",
"2. ①にJOINT SILENCER を取付"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"In... | [
{
"WorkName": "配線・JOINT取付",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付けてある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(2/3)",
"Words": [
"締付けﾄﾙｸ:3.2N･m",
"締付けﾄﾙｸ:70cN･m",
"3㎜ﾌﾞﾛｯｸｹﾞｰｼﾞ"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付",
"2. ①に③をBOLT WASHER で取付け"
],
"WorkPoints": [
"段差部と平行に取付ける為にﾌﾞﾛｯｸｹﾞｰｼﾞをはさむ事",
"③を取付ける際ｴｱｰﾁｭｰﾌ... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ(2/3)",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"Words": [
"◆3. ④を取付",
"LCG100",
"LCG100",
"③",
"締付けﾄﾙｸ:3.2N･m",
"緩めて､再締結",
"LCG100",
"締付けﾄﾙｸ:3.2N･m",
"③⑯",
"②",
"⑯⑰",
"②の取付け面は①より上面に出ないこと",
"締付けﾄﾙｸ:3.2N･m",
"ｸﾞﾘｰｽ塗布 米粒:1 ... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ(3/3)",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2124",
"ToolName": "ﾍｯﾄﾞｵﾌﾟｼｮﾝ駆動ﾕﾆｯﾄ組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "調整1",
"Words": [
"150cN･m",
"320cN･m",
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"片当り､隙間無い事",
"片当り､隙間無い事",
"締付けﾄﾙｸ: 150cN･m",
"締付けﾄﾙｸ: 320cN･m",
"調整部のﾎﾞﾙﾄ",
"検査表①:ﾎﾙﾀﾞ取付確認"
],
"WorkItems": [
"1. 駆動部に治具... | [
{
"WorkName": "調整1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN･m±10%cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "調整2",
"Words": [
"調整ﾎﾞﾙﾄ",
"0.02mmのｼｯｸﾈｽｹﾞｰｼﾞが通らないこと",
"3mmﾌﾞﾛｯｸｹﾞｰｼﾞ(ﾌﾟﾚｰﾄ)を挟み平行に調整",
"締付けﾄﾙｸ: 3.2N･m",
"検査表①:ｼﾘﾝﾀﾞｰ調整 ｼﾘﾝﾀﾞｰ位置調整"
],
"WorkItems": [
"2. ｼﾘﾝﾀﾞ部の調整をする",
"1. 治具を置きP601/P602の位置きめを行う"
],
"WorkPoints... | [
{
"WorkName": "調整2",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2124",
"ToolName": "ｼﾘﾝﾀﾞｰﾌﾞﾛｯｸ保持治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに取付けある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾌﾞﾗｹｯﾄ取付と配管接続",
"Words": [
"締付けﾄﾙｸ: 95cN･m"
],
"WorkItems": [
"2. ①へ③を配管の接続を行う",
"1. ①に③を⑯⑰で取付け",
"3. 配管と一緒に固定"
],
"WorkPoints": [
"傾きが無いように下へ押し下げた状態で取付け"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos"... | [
{
"WorkName": "ﾌﾞﾗｹｯﾄ取付と配管接続",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "150cN・m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ開閉機能検査",
"Words": [
"\"閉限\"ON",
"SW\"閉限\"",
"ｼﾘﾝﾀﾞｰ動作",
"ｼﾘﾝﾀﾞｰ動作",
"\"開限\"ON",
"SW\"開限\""
],
"WorkItems": [
"･機能検査装置(ﾁｪｯｶｰ)と駆動部のｴｱｰ配管と電源を接続して､以下の動作を確認する｡･SW:開限側→ﾗﾝﾌﾟ開限ON→ｼﾘﾝﾀﾞｰ前進･SW:閉限側→ﾗﾝﾌﾟ閉限ON→ｼﾘﾝﾀﾞｰ後進"
... | [
{
"WorkName": "ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ開閉機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Others": "-",
"Process... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"2ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"SW\"開\"側",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"上"
],
"WorkItems": [
"1. ①ﾁｪﾝｼﾞｬｰの自重落下確認 2ﾉｽﾞﾙﾁｪﾝｼ... | [
{
"WorkName": "2ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"8ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"上",
"下",
"2ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側"
],
"WorkItems": [
"1. ①ﾁｪﾝｼﾞｬｰの自重落下確認... | [
{
"WorkName": "8ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"Words": [
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"12ﾉｽﾞﾙﾗﾝﾌﾟ点灯する事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"上",
"下",
"12ﾉｽﾞﾙ治具をｾｯﾄ",
"SW\"開\"側"
],
"WorkItems": [
"1. ①ﾁｪﾝｼﾞｬｰの自重落... | [
{
"WorkName": "12ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Others": "-",
"Process... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"Words": [
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ使用",
"ﾚﾊﾞｰを押す",
"自重落下",
"目視:隙間無い事",
"ｼｬｯﾀｰ\"開\"",
"SW\"閉\"側",
"ｼｬｯﾀｰ\"閉\"",
"上",
"下",
"3(2)ﾉｽﾞﾙ治... | [
{
"WorkName": "3ﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査",
"QualityItem": "動作確認",
"ToolManageNo": "FM-2169",
"ToolName": "NPMﾉｽﾞﾙﾁｪﾝｼﾞｬｰ機能検査治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに動作する事",
"Method": "目視",
"RecordMethod": "WDQB-F013-006",
"Others": "-",
"ProcessN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ﾗﾍﾞﾙ貼付け_2",
"Words": [
"74mm",
"1mm",
"74mm",
"1mm"
],
"WorkItems": [
"1. ①に②⑥を貼付け"
],
"WorkPoints": [
"①の貼付け部分の油分･ごみ等を除去する"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],... | [
{
"WorkName": "ﾗﾍﾞﾙ貼付け_2",
"QualityItem": "貼付確認",
"ToolManageNo": "-",
"ToolName": "ｽｹｰﾙ",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "作業指示通りに貼付けてある事",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "ｸﾞﾘｰｽ塗布",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:1",
"10mm程度"
],
"WorkItems": [
"◆1. ｸﾞﾘｰｽｱｯﾌﾟを実施"
],
"WorkPoints": [
"2,8,12ﾁｪﾝｼﾞｬｰ接触面にｸﾞﾘｰｽ塗布(各ﾁｪﾝｼﾞｬｰとこすれが生じる箇所)",
"赤丸部:ｸﾞﾘｰｽ塗布部分",
"青丸部:ｸﾞﾘｰｽ塗布部分"
],
"Tolks": [],
"Inspect... | [
{
"WorkName": "ｸﾞﾘｰｽ塗布",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "米粒/1粒",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-W2：ﾍｯﾄﾞオプション駆動ユニット",
"WorkName": "出荷準備",
"Words": [
"PLATE 検査書有無確認(N210142855)検査書が添付されている事｡"
],
"WorkItems": [
"1. ﾁｪﾝｼﾞｬｰ駆動部ﾕﾆｯﾄ(本体1台当たり2ﾕﾆｯﾄ使用)"
],
"WorkPoints": [
"ﾌﾛﾝﾄ用:ｺﾈｸﾀB03R､B04R､B05R､B06R ﾘｱ用 :ｺﾈｸﾀB13R､B14R､B15R､B16R"
],
"Tolks": [],
"InspectionI... | [
{
"WorkName": "出荷準備",
"QualityItem": "準備確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りに準備してある事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"Words": [],
"WorkItems": [
"1. VALVE にJOINT SILENCER JOINT を取付ける",
"2. 1完成品にTUBE を取付ける"
],
"WorkPoints": [
"TUBE を120㎜にｶｯﾄする",
"ｻｲﾚﾝｻの根元を掴んで取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 1.2N･m"
],
"InspectionItems": [],
... | [
{
"WorkName": "ﾊﾞﾙﾌﾞ組立",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸｽﾊﾟﾅ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "1.2N･m±10%",
"Method": "ﾄﾙｸｽﾊﾟﾅ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｼﾘﾝﾀﾞ組立1",
"Words": [],
"WorkItems": [
"2. BLOCK にSPACER BEARING をBOLT で取付ける",
"1. BLOCK に防錆油を塗布する"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPa... | [
{
"WorkName": "ｼﾘﾝﾀﾞ組立1",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"Words": [
"付属ﾅｯﾄ",
"付属ﾅｯﾄ",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:1",
"全体にｸﾞﾘｰｽ塗布 米粒:1"
],
"WorkItems": [
"6. ｼﾘﾝﾀﾞのｽﾄﾛｰｸを調整し付属ﾅｯﾄで固定する",
"◆3. WASHER GUIDE WASHER SPRING にｸﾞﾘｰｽを塗布する",
"4. CYL... | [
{
"WorkName": "ｼﾘﾝﾀﾞ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｼﾘﾝﾀﾞ組立3",
"Words": [
"締付けﾄﾙｸ: 95cN･m"
],
"WorkItems": [
"1. ①にPLATE BLOCK をBOLT WASHER で仮固定",
"2. 1完成品を㉛に装着し締結する"
],
"WorkPoints": [
"治具とｽｷﾏ無きよう当付ける",
"①を治具の段差部に乗せる",
"①やPLATE の中央部を下方向に当付ける",
"押さえた指はそのままで、㉖と㉗で締結す... | [
{
"WorkName": "ｼﾘﾝﾀﾞ組立3",
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolName": "位置合わせ治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"Words": [
"(出限)",
"(戻限)",
"取付方向確認側面にｼﾞｮｲﾝﾄ取付穴有",
"出限",
"戻限",
"ｾﾝﾀｰ",
"⇧ＬＳ調整位置",
"約3㎜",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"右側より近づけてONする位置",
"左側より近づけてONする位置",
"ＬＳ調整位置⇩",
"約3㎜",
... | [
{
"WorkName": "ｼﾘﾝﾀﾞ組立4",
"QualityItem": "位置確認",
"ToolManageNo": "FM-6131",
"ToolName": "位置合わせ治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り作業出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾋﾟﾝ圧入1",
"Words": [
"320cN･m"
],
"WorkItems": [
"1. BRACKET にPIN を圧入し防錆油を塗布する",
"2. LEVER に砥石をかけ防錆油を塗布する",
"3. 1完成品にLEVER をBOLT で仮止めし､圧入後本締めする"
],
"WorkPoints": [
"ﾋﾟﾝ出代:3.5㎜",
"3.5㎜",
"両面に砥石"
],
"Tolks": [
... | [
{
"WorkName": "ﾋﾟﾝ圧入1",
"QualityItem": "PIN出代",
"ToolManageNo": "FM-4532",
"ToolName": "ﾌﾞﾗｹｯﾄﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "出代:3.5㎜",
"Method": "ｽｹｰﾙ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾚﾊﾞｰ組立1",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"1. PLATE に砥石をかけ防錆油を塗布する",
"◆2. WASHER にｸﾞﾘｰｽを塗布する",
"3. ④にWASHER を入れ､PLATE にWASHER BOLT で取付ける",
"4. 3完成品にBOLT を取付ける"
],
"WorkPoints": [
"両面に砥石",
"外周にｸﾞﾘｰｽを塗布"... | [
{
"WorkName": "ﾚﾊﾞｰ組立1",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾚﾊﾞｰ組立2",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:2",
"ｸﾞﾘｰｽ塗布 米粒:2"
],
"WorkItems": [
"1. LEVER に砥石をかけ､防錆油を塗布する",
"◆2. BUSH にｸﾞﾘｰｽを塗布する",
"3. ⑥にLEVER をBUSH ③BOLT で仮取付けする",
"◆4. BOLT にｸﾞﾘｰｽを塗布する",
"5. BOLT にWASHER SPRING WASHER を通し､3完成品... | [
{
"WorkName": "ﾚﾊﾞｰ組立2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｸﾗﾝﾌﾟ組立1",
"Words": [],
"WorkItems": [
"1. LEVER LEVER BRACKET SHAFT の指示部に砥石をかけ防錆油を塗布する"
],
"WorkPoints": [
"面取りの箇所は取付け部か摺動部の為充分に拭きあげておくこと",
"表裏部",
"左右上面",
"端面"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos... | [
{
"WorkName": "ｸﾗﾝﾌﾟ組立1",
"QualityItem": "組立確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通りの作業が出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｸﾗﾝﾌﾟ組立2",
"Words": [
"ｸﾞﾘｰｽ塗布 ｺﾞﾏ粒:各1"
],
"WorkItems": [
"1. SPACER にBEARING WASHER ④をBOLT WASHER で取付ける",
"2. 1完成品にBEARING WASHER ⑤をBOLT WASHER で取付ける",
"◆3. ⑦にｸﾞﾘｰｽを塗布する",
"4. ⑥に3完成品を入れる",
"5. 4完成品をWASHER BOLT で仮取付けする"
]... | [
{
"WorkName": "ｸﾗﾝﾌﾟ組立2",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布ｺﾞﾏ粒:1",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ｸﾗﾝﾌﾟ組立3",
"Words": [
"A",
"A",
"B",
"B",
"締付ﾄﾙｸ 150cN･m"
],
"WorkItems": [
"1. ①を治具に取付ける",
"2. Aを締付ける",
"3. Bを締付ける"
],
"WorkPoints": [
"浮きが無いこと確認しﾚｰﾊﾞｰを締めて固定する",
"締付けの際浮きが無いことを確認し締付ける",
"締付けの際... | [
{
"WorkName": "ｸﾗﾝﾌﾟ組立3",
"QualityItem": "取付確認",
"ToolManageNo": "FM-4062",
"ToolName": "ｸﾗﾝﾌﾟ部組立治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾌﾟﾚｰﾄの砥石がけ",
"Words": [
"□印面と矢印の面と裏面"
],
"WorkItems": [
"1. PLATE に砥石をかける",
"2. PLATE に防錆油を塗布する"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
... | [
{
"WorkName": "ﾌﾟﾚｰﾄの砥石がけ",
"QualityItem": "外観確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "ｷｽﾞ無い事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾋﾟﾝ圧入2",
"Words": [],
"WorkItems": [
"1. ①にPIN PIN を圧入する"
],
"WorkPoints": [
"ﾋﾟﾝ出代:5㎜",
"ﾋﾟﾝ出代:11㎜"
],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [],
"WorkTypes": [],
"ToolPartsModels": [
{
"Jigu... | [
{
"WorkName": "ﾋﾟﾝ圧入2",
"QualityItem": "取付確認",
"ToolManageNo": "FM-2254",
"ToolName": "ﾍﾞｰｽDﾋﾟﾝ圧入治具",
"ToolCycle": "校正対象外",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾌﾟﾚｰﾄ組立1",
"Words": [
"ｸﾞﾘｰｽ塗布 米粒:各2"
],
"WorkItems": [
"◆1. SPRING SPACER の外周にｸﾞﾘｰｽを塗布する",
"2. BOLT にSPRING WASHER SPACER を通す",
"3. 2完成品を①にWASHER NUT で取付ける"
],
"WorkPoints": [],
"Tolks": [
"締付ﾄﾙｸ 95cN･m"
],
"Inspe... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立1",
"QualityItem": "塗布量",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示箇所に塗布米粒:2",
"Method": "目視",
"RecordMethod": "-",
"Others": "ｸﾞﾘｰｽLCG100",
"ProcessNames": [
"-"
]
},
{
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾌﾟﾚｰﾄ組立2",
"Words": [
"A"
],
"WorkItems": [
"2. ②に③を⑯⑰⑱で取付ける",
"3. 2完成品を①に⑱⑲で取付ける",
"1. ②に防錆油を塗布する",
"4. 3完成品のｾﾝｻON/OFF確認を行う"
],
"WorkPoints": [
"A矢視",
"ﾎﾞﾙﾄがｾﾝｻのｾﾝﾀｰになる事",
"ｻﾝｻｰ押し当て",
"4個の全てのｾﾝｻを確認する事",... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "40cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾌﾟﾚｰﾄ組立3",
"Words": [],
"WorkItems": [
"3. 2完成品にCLIP をBOLT で取付ける",
"2. ①にGUIDE をBOLT で取付ける",
"1. GUIDE に防錆油を塗布する"
],
"WorkPoints": [
"下側に当付けて取付けの事",
"下側に当付けて取付けの事"
],
"Tolks": [
"締付ﾄﾙｸ 110cN･m",
"締付ﾄﾙｸ 95cN･m"
... | [
{
"WorkName": "ﾌﾟﾚｰﾄ組立3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "95cN･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾄﾞｯｷﾝｸﾞ1",
"Words": [
"2. 1完成品"
],
"WorkItems": [
"1. ①に②をBOLT WASHER で取付ける",
"2. 1完成品にCLIP をBOLT で取付ける",
"3. 2完成品に③をBOLT WASHER で取付ける"
],
"WorkPoints": [
"調整後に指定ﾄﾙｸで仮締め締付けはSD-A003681-022にて締め付け",
"ﾌﾞﾛｯｸｹﾞｰｼﾞを挟み込んで仮位置を出... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ1",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
},
{
"WorkN... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "配線・JOINT取付け",
"Words": [
"ｲﾝｼｭﾛｯｸ指示",
"･ｹｰﾌﾞﾙ同士を固定",
"･ﾀｲﾏｳﾝﾄに固定 又は板金に固定"
],
"WorkItems": [
"1. ①の配線を固定する",
"2. 1完成品にJOINT SILENCER を取付ける"
],
"WorkPoints": [],
"Tolks": [],
"InspectionItems": [],
"InspectionNos": [... | [
{
"WorkName": "配線・JOINT取付け",
"QualityItem": "取付確認",
"ToolManageNo": "-",
"ToolName": "-",
"ToolCycle": "-",
"ToolRecord": "-",
"StdVal": "指示通り取付出来ている事",
"Method": "目視",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
]
}
] | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾄﾞｯｷﾝｸﾞ2",
"Words": [
"折り曲げ部と平行に",
"矢印方向に押し当て"
],
"WorkItems": [
"3. 2完成品に③をBOLT WASHER で取付ける",
"1. BRACKET に防錆油を塗布する",
"2. ①にBRACKET をBOLT WASHER で取付ける"
],
"WorkPoints": [
"ﾌﾞﾗｹｯﾄ面とﾊﾞﾙﾌﾞ継ぎ手面を合わせて取付けの事"
],
"Tolks... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ2",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾚﾝﾁ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾚﾝﾁ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
"-"
... | information_extraction | 0 | null | |
{
"UnitName": "NPM-DX ：ﾍｯﾄﾞOP駆動ﾕﾆｯﾄ",
"WorkName": "ﾄﾞｯｷﾝｸﾞ3",
"Words": [
"②の取付け面は①より上面に出無い事",
"片当り､隙間無い事",
"片当り､隙間無い事"
],
"WorkItems": [
"2. 駆動部に治具を置く",
"3. ﾍﾞｱﾘﾝｸﾞの当りを調整する",
"4. 各調整部のﾎﾞﾙﾄを締結する",
"1. ①に②をBOLT WASHER ･WASHER BOLT で取付ける"
],
"WorkPoints": [
"調整部... | [
{
"WorkName": "ﾄﾞｯｷﾝｸﾞ3",
"QualityItem": "締付ﾄﾙｸ",
"ToolManageNo": "-",
"ToolName": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"ToolCycle": "日常点検(1回/日)",
"ToolRecord": "ﾄﾙｸﾁｪｯｸ台帳",
"StdVal": "3.2N･m±10%",
"Method": "ﾄﾙｸﾄﾞﾗｲﾊﾞｰ",
"RecordMethod": "-",
"Others": "-",
"ProcessNames": [
... | information_extraction | 0 | null |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.